[Potato] How to use and monitor reverb

[neilj99]

Hi,

I’m currently trying Potato.

I haven’t figured out how to monitor the internal reverb effects via my headset.

I’d like to add a spot effect to my mic.

I’m using VM and streaming on the same system.

How do I get the effects to work?

Thanks.

Neil.

[Vincent Burel]

simply set the REVERB SEND to max (10.0) on your microphone strip
and set the REVERB RETURN to max (10.0) on the wanted BUS.

VoicemeeterPotatoSendToRverbFx.jpg (228.91 KiB) Viewed 31084 times

[neilj99]

Many thanks.

I’ll give it a go.

Absolutely love the software.

Neil

P.S. Whilst I think of it, is there a way to assign a keyboard hotkey to toggle the effect?

[Vincent Burel]

for the moment the following new instructions are implemented:

Strip.Reverb 0 to 10 Send Level To Reverb
Strip.Delay 0 to 10 Send Level To Delay
Strip.Fx1 0 to 10 Send Level To External Fx1
Strip.Fx2 0 to 10 Send Level To External Fx2
Strip.PostReverb 0 (off) or 1 (on) Post Reverb button
Strip.PostDelay 0 (off) or 1 (on) Post Delay button
Strip.PostFx1 0 (off) or 1 (on) Post Fx1 button
Strip.PostFx2 0 (off) or 1 (on) Post Fx2 button

Bus.Sel 0 (off) or 1 (on) BUS SEL Button
Bus.ReturnReverb 0 to 10 Reverb return
Bus[i].ReturnDelay 0 to 10 Delay return
Bus[i].ReturnFx1 0 to 10 FX1 return
Bus[i].ReturnFx2 0 to 10 FX2 return

[neilj99]

Apologies.

I was just wondering how to assign a keyboard keystroke to the effect.

The above has confused me slightly.

N.

[Vincent Burel]

with MacroButtons

[neilj99]

Hi,

I can't get the reverb to come through OBS.

I have A1 set as my headset.
I have strip 1 set as Cabel A - Mic >A1 >B1
I have strip 2 set as Cabe B - TTS >A1 local only
I have strip 6 set as Mic VM VAIO >A1 >B2
I have strip 7 set as System Audio VM AUX >B2

I would like to hear the reverb and send it to OBS (Cable A Output at OBS).

Thanks,

N.

[JBP]

It is important to understand that all the virtual B-busses (B1, B2, B3) represent VAIO not related to VB Cables.

If you want to use VB Cable-A as input (Cable-A Output) in OBS then you have to select Cable-A Input as a hardware out (A1, A2, A3, A4, A5) in Potato!
Then you adjust the FX return for that specific output.

[neilj99]

Hi,

If I select Cable A Input as A2 (A1 is my headset), then Audition fails, as in Audition, I have my mic as input and Cable A Input as output. I EQ my mic through Audition.

I seem to be getting nowhere fast.

N.

[JBP]

Hi,

If I select Cable A Input as A2 (A1 is my headset), then Audition fails, as in Audition, I have my mic as input and Cable A Input as output. I EQ my mic through Audition.

I seem to be getting nowhere fast.

N.

If you have Cable A then you also have Cable B and the standard Cable.
So you have this three (3!) Cables and A1 plus four other outputs (A2 to A5) you can use with all Cables:
VB Cable + VB Cable A + VB Cable B